How to adjust your motorcycle suspension

Harley Davidson with open views in the background

Adjusting your motorcycle’s suspension for better handling can dramatically improve your ride’s comfort, control, and safety. Follow these steps to tune your suspension to suit your riding style, weight, and road conditions.

Step 1: Understand Your Suspension Components

Before you start adjusting, know the three primary settings on your bike’s suspension:

• Preload: Adjusts the amount of weight on the springs before compression, affecting ride height and sag.

• Compression Damping: Controls how fast the suspension compresses when hitting a bump.

• Rebound Damping: Controls how quickly the suspension extends back after compression.

Step 2: Find Your Factory Settings

Check your owner’s manual to locate your suspension settings and identify stock settings. This gives you a baseline if you need to reset. The manual will also indicate the location of preload, compression, and rebound adjustment points, usually on the top and bottom of the forks and near the rear shock.

Step 3: Set Your Sag

Setting the proper sag (the amount the suspension compresses under the rider’s weight) is essential for optimal handling.

Tools Needed:

• Tape measure

• Friend to help with measurements

• Spanner/socket (for preload adjustment)

Steps:

1.  Free Length/Full extension: Lift the bike so the wheels are off the ground so the suspension is fully extended. Measure the distance between a fixed point in the direction of suspension travel to the centre of the axle.

2. Measure Free Sag: With the bike on a stand (no weight on it), measure the distance from a fixed point on the bike’s frame to the axle center.

3. Measure Rider Sag: Sit on the bike in full gear in your normal riding position. Have a friend re-measure the same points. The difference between free sag and rider sag is your “sag” measurement.

4. Adjust Preload: Adjust the preload to set the sag within recommended values (typically 25-30% of the total suspension travel for street riding).

Step 4: Adjust Compression Damping

Compression damping adjustments can improve how your bike handles bumps and dips in the road.

1. Start with the manufacturer’s recommended settings as a baseline.

2. To increase compression damping (firmer ride): Turn the adjustment screw clockwise.

3. To decrease compression damping (softer ride): Turn the adjustment screw counterclockwise.

4. Test the bike’s handling by riding over bumps. Adjust until you feel controlled absorption without harshness.

Step 5: Adjust Rebound Damping

Rebound damping affects how quickly the suspension returns to its normal position after absorbing a bump.

1. With the bike still on baseline settings, bounce on the seat while observing how the suspension settles.

2. Increase rebound damping if the bike feels like it’s bouncing back up too quickly, which indicates too little damping.

3. Decrease rebound damping if the bike takes too long to settle, which could make it feel sluggish.

4. Fine-tune by riding on a typical road surface and noting how the bike settles after hitting a bump.

Step 6: Test Ride and Fine-Tune

1. Take your bike for a test ride over varied terrain (twisties, rough surfaces, straights) to see how it handles.

2. Adjust one setting at a time (small increments) to feel the changes.

3. Repeat adjustments if necessary to dial in a comfortable, controlled setup.

Step 7: Keep Track of Adjustments

Write down your adjustments after each ride or significant change. Recording these settings helps you track what works best for specific conditions or lets you reset to a known good setup.

Step 8: Check for Balance

Ensure that your front and rear suspensions are balanced. If one end feels stiffer or softer than the other, fine-tune both preload, compression, and rebound settings to maintain even handling.

• Tweak in Small Increments: Small adjustments make a big difference. Start with 1–2 clicks or half turns.

• Be Patient: Suspension tuning can take a few test rides to dial in perfectly.

• Consider Your Riding Style: Aggressive riders may prefer stiffer setups, while casual riders might prefer a softer, more forgiving ride.

Following these steps will help you get the most out of your bike’s suspension for improved handling and a more enjoyable ride.

Why Not Book Your Motorcycle Suspension or Fork Service Now...

Speech Quote Icon

Amazing and quick service for such a tedious process, recently did my Daytona 675 USD forks spent the time to get them right and didn’t keep me in the dark , told me what exactly was wrong etc
Recommend will be using again

Jacob Elson

Excellent service of my WP forks on my CCM404, a very quick turn around. It transformed my bike. Thanks once again Harry

Daniel Hutton

I can't quite articulate how or what in particular but the bike handled so much better especially under breaking and in the corners! I felt like I had more control and feel! So overall definitely needed doing. Really pleased mate, thank you

Frank Hymas

Thanks for turning around my forks so quickly. I managed to make the race at the weekend, which meant I came third in my local centre championship.

Ben CRF250R

I didn't realise how bad my shock had got until i rode it after you serviced it! Best money i've spent on the bike in years. I will send you the forks when we get back from our euro road trip.

Dan VFR800

Just a quick note to say thanks for sorting the forks and shock on my mini twin. It’s gone from feeling like an old commuter bike on track to a proper race bike, and I went 3 seconds a lap faster at Snett!

Jason Davey

Shopping Basket
Scroll to Top